Guickstart Guide of VS-GW1600-20G Connect with VOS3000 Operation Platform

This document applies to OpenVox GSM Gateway WGW1002,VS-GW1202-4/8G and VS-GW1600 series.

There are two RJ45 Network ports, ETH1 and ETH2. If you choose ETH1, you can access Board 1 only, and access other boards with the same IP address, different port numbers. This will help to avoid IP conflict. If you choose ETH2, you can access different Boards with different IP addresses. But there is only one RJ45 Network port on WGW1002.

VoxStack provides 2 working modes: Stand-alone and Cluster.

• Stand-alone: A single IP address manages one GSM modules (4 ports).

• Cluster: A single IP address manages up to 5 GSM modules (up to 20 ports). 
   
                                Default IP: 172.16.99.1 
                                User Name: admin
                                Password: admin
  

If your system topology like the figure described, please enter the gateway default IP address In your browser to login web, and click “NETWORK—>LAN Settings” to set network parameters such as IP.

Save your changes. Please type in your DNS server in “DNS Server Address”.

Please select “SIP—>SIP Endpoints—>Add New SIP Endpoint” to set SIP trunk. The following figure shows detail information about how to set it.

About other parameters in SIP, please set by your requirements for there is no need to set them in simple calls.

Click “ROUTING—> Call Routing Rules—> New Call Routing Rule” to set outbound and inbound routing rules like the following:

Save the inbound call routing rules, please set the outbound rules as introduced. In order to make all calls successfully, please enable and set failover function in advanced routing rule like that:

Please save all your changes to make effect.

There are 2 kinds of Gateway in VOS3000 Operation Platform: Routing Gateway and Mapping Gateway. Routing Gateway is for VOS3000 to PSTN while Mapping Gateway is opposite. If you need both outbound and inbound calls from GSM gateway, then you need create both Routing Gateway and Maping Gateway to make it happen. 

Section 1: Add a Routing Gateway in register mode: 

Please select “Operation Management---> Gateway Operation----- > Routing Gateway" to create a Routing Gateway: 

Gateway ID:1001 ---------------------Username of SIP trunk which GSM gateway registers to 

Password:1001 ---------------------Password of SIP trunk which GSM gateway registers to 

Gateway Prefix:9 ---------------------Specify calleeID 9+number goes out from GSM gateway

Additonal Settings:

● Normal---->Gateway Type---->Dynamic 

VOS3000 here acts as a SIP server, OpenVox GSM Gateway as a SIP client registers to it.

● Routing Prefix---->Routing Callee Rewrite 

Add a Routing callee Rewrite Rule to remove the prefix '9' of CalleeID, then send it to GSM gateway.

● Advanced---->SIP------Authentication User & Password

When Register enabled, Authentication Uaser and Password must be filled in.

● Register------>On

This option is to choose register mode or ungister mode for GSM gateway.

Section 2: Add a Mapping Gateway in register mode:

Please select “Operation Management ---> Gateway Operation ---> Mapping Gateway" to create a Mapping Gateway:

Gateway ID:1001 --------------------- Username of SIP trunk which GSM gateway registers to

Password:1001 ---------------------  Password of SIP trunk which GSM gateway registers to 

Additonal Settings: 

● Normal---->Gateway Type---->Dynamic

● Mapping Prefix---->Mapping Callee Rewrite

 Add a RMapping callee Rewrite Rule to match all calls from GSM gateway, then send it to extension 4001.

Apply all changes on VOS3000 and GSM gateway, then you can try to make calls.

Taking advantage of SIP software such as Xlite, eyeBeam to register a SIP extension(4001) on VOS3000 server.

● Test call from VOS3000 to GSM geteway

Use Extension 4001 to call 9+number, then you will reach the number you want through GSM gateway, you can check it on GSM gateway.

● Test call from GSM geteway to VOS3000

Use your mobile to call numbers of SIM cards on GSM gateway, then Extension 4001will be ringing.

Front Panel

LED Indicator	Color	Status
Network Status LED	Green and Flash	Network Connected
Signal Status LED	Green and Flash	Module Initiating
	Red and Flash	No SIM Card
	Red and No-flash	Worst Signal Quality
	Yellow and No-flash	Medium Signal Quality
	Green and No-flash	Best Signal Quality
Call Status LED	Flash (0.25s)	Communicating
	Blind	Normal
Running Status LED	Green and Flash(0.5s)	Work Normally
Power Indicator	Always Green	Supply Power
During reset, all LED indicators flash.