IX132 Series IP-PBX User Manual

Chapter 1 Software Installation

IX132 series IP-PBX supports combinations analog, BRI, PRI and GSM telephony cards, now let’s take the combination of A400E and DE130E for an example to illustrate software installation. And assume that DE130E need to run in SS7 signaling.

 

1.1 Download

Download chan_ss7 package from:

http://www.netfors.com/chan_ss7_free

Get DAHDI source package from openvox:

http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/openvox_dahdi-linux-complete-current.tar.gz

Get Asterisk software package from digium official website:

http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-1.8.0.tar.gz

 

Execute the following commands in the directory /usr/src/ in general to download and unzip the three source packages.

 

#_wget_http://www.netfors.com/media/download/chan_ss7-2.1.0.tar.gz

#_wget_http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/openvox_dahdi-linux-complete-current.tar.gz

#_wget_http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-1.8.0.tar.gz

# tar_-xvzf chan_ss7-2.1.0.tar.gz

#_tar_-xvzf_openvox_dahdi-linux-complete-xx.tar.gz

# tar –xvzf asterisk-1.8.0.tar.gz

 

1.2 Installation

Make sure your necessary dependencies have all been installed, and then get start to install DAHDI, Asterisk and chan_ss7.

 

# cd /usr/src/dahdi-linux-complete-XX

# make

# make install

# make config

 

   Caution: If there is something wrong after "make", please refer to HERE. In the url link, the moderator introduces you a method how to patch. After patching, save your changes and exit. Then run "make" again, if successfully, you are going to install Asterisk.

 

Please operate those commands to install Asterisk.

 

# cd asterisk-1.8.0

# ./configure

# make

# make install

# make samples

 

      " make samples" will install the standard sample configuration file in the directory /etc/asterisk. As a freshman, you should perform make samples, that is to say, it is unnecessary to perform make samples every time. Because once performed, it will cover the old sample configuration files you have installed.

 

After installed dahdi and asterisk, now install chan_ss7 as below:

Go to the directory of chan_ss7 source codes and modify Makefile like this:

#INCLUDE+=-I../source/telephony/zaptel/kernel

#CFLAGS+=-DUSE_ZAPTEL

ASTERISK_PATH=../asterisk-1.8.0/include

INCLUDE+=-I../dahdi-linux-complete-2.3.0.1+2.3.0/include

 

Execute commands to compile and install chan_ss7

 

 

 

1.3 Configuration

1. Driver loading

After compiling and installing DAHDI and Asterisk, please load the driver by running:

 

# modprobe dahdi

# modprobe opvx115

# modprobe wctdm

# dahdi_genconf

 

After running, there is not any indication information displayed if loaded normally and successfully. "opvx115" and "wctdm" are the driver module name of DE130E and A400E.

 

If there is any error, please trace the cause. Until all errors are clear up, you could execute "dahdi_genconf" again, and then go to the next step. By running "dahdi_genconf", it will generate /etc/dahdi/system.conf and etc/asterisk/dahdi-channels.conf automatically. Checking whether the generated files information agrees with your hardware setup, if not, you should modify to your specific requirements. Do not forget to confirm dahdi-channels.conf is included in chan_dahdi.conf, if not, run command:

 

# echo "#include dahdi-channels.conf" >> /etc/asterisk/chan_dahdi.conf

 

FXO ports use FXS signaling, while FXS ports adopt FXO signaling. A part of system.conf which is one of the basic channel configuration files is displayed.

 

                      Figure 6 A part of system.conf

 

 

    Some zonedata is available in the file

 

..  /dahdi-XX/tools/zonedata.c, you can refer to it to match your country mode. Meanwhile, you also need to modify another parameter which is in file                                               /etc/asterisk/indications.conf.

 

country=cn

2. Edit files for ss7

a. Edit /etc/dahdi/system.conf like:

 

b. edit /etc/asterisk/ss7.conf

 

Some parameters in this file need to be changed according to your situation. Please replace “zmdvoip” by your asterisk server name. If “opc” is 0x10fff6 and “dpc” is 0x10ff48 carrier gives you, you must set

opc => 0x10ff48 dpc => siuc:0x10fff6” like the above figure.

 

c. Edit /etc/asterisk/dahdi-channels.conf

Please comment out the settings for DE130E, otherwise it will be contradictory with ss7

 

After these tasks finished, please execute the following command:

# service dahdi restart

# dahdi_cfg –vvvvvv

 

The command is used for reading and loading parameters in the configuration file system.conf and writing to the hardware. A part of outputs are showed in the following figure.

                            Figure 7 Channel map

 

3. Asterisk initiation

 

# asterisk -vvvvvvvgc

 

If Asterisk is already activate, run "asterisk –r" instead. In the CLI, please run the following command:

localhost*CLI> ss7 link status

linkset siuc, link l1/16 INSERVICE, sls 0, total: 8684336, 8684368

localhost*CLI> ss7 linestat

Linkset: siuc

CIC   0 Idle

CIC   1 Idle            

CIC   2 Idle             

CIC   3 Idle            

CIC   4 Idle            

CIC   5 Idle            

CIC   6 Idle           

CIC   7 Idle            

CIC   8 Idle            

CIC   9 Idle           

CIC  10 Idle            

CIC  11 Idle            

CIC  12 Idle             

CIC  13 Idle            

CIC  14 Idle            

CIC  16 Idle

CIC  17 Idle            

CIC  18 Idle            

CIC  19 Idle            

CIC  20 Idle            

CIC  21 Idle            

CIC  22 Idle            

CIC  23 Idle            

CIC  24 Idle            

CIC  25 Idle            

CIC  26 Idle            

CIC  27 Idle            

CIC  28 Idle            

CIC  29 Idle            

CIC  30 Idle            

 

localhost*CLI> dahdi show channels

                          Figure 9 channels show

 

If DAHDI channels and ss7 are found and up, it means they have been loaded into Asterisk successfully. The last thing is to edit your extension (softphone or hard phone) and dialplan by your requirements. After right dialplan, I will say “congratulations to you!”

 

After saving your dialplan, please run "asterisk –r", then execute "reload" in the CLI. Next you are able to make calls.

Chapter 2 Reference

www.openvox.cn

www.digium.com

www.asterisk.org

www.voip-info.org

www.asteriskguru.com

 

Tips

Any questions during installation please consult in our forum or look up for answers from the following websites:

Forum

wiki

 

Appendix

# yum install bison

# yum install bison-devel

# yum install ncurses

# yum install ncurses-devel

# yum install zlib

# yum install zlib-devel

# yum install openssl

# yum install openssl-devel

# yum install gnutls-devel

# yum install gcc

# yum install gcc-c++

# yum install libxml2